Advanced Diploma in Electrical Design Engineering




Advanced Diploma in Electrical Design Engineering

The goal is to design safe and dependable processing facilities in a cost effective manner. The fact is that there are very few formal training programs that focus on design and engineering of Electrical systems of such big plants The heavy electrical industry has under its purview power generation, transmission, distribution and utilization equipment. These include turbo generators, boilers, turbines, transformers, switchgears and other allied items. These electrical equipment (transformers, switchgears, etc.) are used by almost all the sectors. Some of the major areas where these are used include power generation projects, petrochemical, refineries, chemical plants, integrated steel plants, non-ferrous metal units, etc.

Overview:-

  • Introduction of Electrical Engineering

  • Introduction of EPC Industry

  • Coordination with Other Department

Load List:-

  • Preparation of Load Schedule

  • Determination of Power Supply Capacity

  • Standby Capacity consideration

  • Rating of Generators in Relation to

  • Prime Movers Importance of max and min temp

  • Rating of Motors in Relation to their Driven Machines

Electrical Equipment Selection, Sizing:-

  • Motor

  • Transformer

  • Emergency Generator

  • Neutral Grounding Resistor (NGR)

  • Power capacitor banks (PCB)

  • AC UPS

  • Battery & Battery Charger

  • CT/PT

  • Bus duct

Illumination Design:-

  • Introduction

  • Type of Lighting Fixtures

  • Selection of Lighting Fixtures

  • Preparation of Fixtures Schedule

  • Indoor Illumination Calculation

  • Outdoor Illumination Calculation

  • Calculation on Software

  • Lighting Layout Design

  • Lighting Installation Detail

  • Small Power selection

  • Lighting Board Schedule

Cable Selection, Sizing & Layout:-

  • Power and Control cable Introduction

  • Cable Selection and Sizing

  • Cable sizing for Low voltage system

  • Cable sizing for High voltage system

  • Voltage Drop Consideration

  • Let through Energy consideration

  • Earth fault Loop Impedance consideration

  • Cable Schedule

  • Cable interconnection Schedule

  • Selection and Sizing of cable Tray

  • Cable tray schedule

  • Cable Drum schedule

  • Conduit Selection

  • Conduit Sizing

  • Cable Routing Layout

  • Cable Tagging

  • Installation details

Development of Single Line Diagram (SLD):-

  • Key SLD

  • Detail SLD

  • Lighting system SLD

  • Small power SLD

  • Metering and Control diagram

Earthing & Lightening Protection Design:-

  • Requirement of Earthing in Industrial Plants

  • Earthing Design calculations

  • Type of Earthing and Details

  • Earthing Installation Details

  • Earthing Layout Design

  • Lightening Protection Requirement

  • Lightening Protection Calculation

  • Lightening Installation Details

  • Lightening Layout Design


  • Testing / System Studies:-

  • Overview & Load Flow Analysis

  • Short Circuit Analysis (Fault Level Calculations)

  • Motor Starting Study

  • Relay- Coordination


Electrical Design Academy: Engineering Training with Practical Examples and Hand-on Training for EPC Sector & MEP Sector

Url: View Details

What you will learn
  • Complete Electrical Design Engineering Training with Practical Example and Hands-on Practice
  • Electrical equipment design for all projects like: oil & gas, chemical, power, pharmaceutical etc.
  • Detail engineering: Single line diagram, cable routing layout, earthing layout, lightening layout, lighting layout, substation layout, equipment layout

Rating: 4.16667

Level: All Levels

Duration: 21.5 hours

Instructor: Rajendra Singh


Courses By:   0-9  A  B  C  D  E  F  G  H  I  J  K  L  M  N  O  P  Q  R  S  T  U  V  W  X  Y  Z 

About US

The display of third-party trademarks and trade names on this site does not necessarily indicate any affiliation or endorsement of hugecourses.com.


© 2021 hugecourses.com. All rights reserved.
View Sitemap